Showing posts with label Manufacturer - Battlefront. Show all posts
Showing posts with label Manufacturer - Battlefront. Show all posts

Sunday, 23 December 2018

Sdkfz 234/2 90% done

90% complete. I need to go and look at the exhaust colour on this otherwise it is done.  Kept this one a lot simpler and only went with the Reseda Opt B over the DGIII basecoat. Tan Filter and a brown pin wash.






Sunday, 14 October 2018

T-64BV Off for painting

Managed to get a base coat on.  Haven't thought about washes or weathering yet. Paint has masked a couple of errors. I didn't finish the prints of properly so they do look a bit rough.  A couple of tweaks needed for any future runs of the prints. Need to look at Antennas and stowage for a cold war soviet look.





Friday, 12 October 2018

T-64BV using the BF Model and a 3D Printer

How hard could it be I said to myself

Carve off some plastic. Print some panels. Job done.

Oh I don't have any scale plans to work off. The BF T-64 engineering tolerances have to be factored in.  PLA isn't easy to glue.

Getting there. Need to work on the B model smoke dischargers and make up some new stowage boxes for the sides of the turret.



In progress, testing out fit and orientation


Very early days checking the print settings, tile thickness and general concept

"The only plan we had"

Wednesday, 3 October 2018

M901 ITV Progress

Managed to get some work done on the M901 ITVs

New MG Rail and periscope added


Crewed and stowed

Base Field Drab

Sand



 Black


Still deciding on decals

Thursday, 20 September 2018

Team Yankee - ITV Section

Having a couple of spare hull tops and loads of components I have looked at options for the M901 ITV.

The top one is straight out of the box.  It is there as a guide for what else needs/could be done.

The lower one is in the stowed for travel position.  I have also repositioned the antenna mount from the front right to the rear part of the hull.  The side plates are included because I have seen them on the 3-Colour drawings of the M901 and change the hull top from a standard M113.  What I also need to find is the reload sequence as I might want to have the top hatch open/crewed on future versions.




Added some stowage and test mounted it on a M113A3 hull that I had lying around to check how it looks.  I have also now added the M60 MG to the commanders hatch




Wednesday, 19 September 2018

Team Yankee - M1 and M1 IPM1s

In the spares box were four M1 abrams.  I have made 3 M1s and one as a IPM1.  I will add another IPM1 later this month.  I also have a couple of M113 hulls left over which I will press into service for the VADS and ITV variants as well as normal troop tracks.

The initial build was two plain M1s. The later models had additional stowage added.  They are all finished in in VJ Dark Green FS 34079 which equates to Forest Green.  I have faded the base coat with some Dark Yellow but worried these are a bit flat. So looking for ideas to brighten these up a tad

















The

Thursday, 13 September 2018

M109G - In Progress

The M109 has come to the painting table.  To make a M109G I needed to add some smoke dischargers and change the cupola over.  To do I that I have used the spare SD from the Leopard 1A3/4 Kits. They aren't correct but are good enough. For the cupola I am going to use a spare M113 one with my standard brass wire MG mount.


I have also tried out using the decals for the Battery and Gun marking. Not 1985 correct but I have evidence that the M109A3 G adopted it at some point.  I am not going to add any more and I think it is a little over the top

Monday, 10 September 2018

Leopard 1A1A1 - 7. PanzerAufklarungsBataillon

Next up are a pair of Leopard 1A1A1 from BF.  Nice kit with a couple of places to do some work.

The barrel is moulded fitted with the environment cap fitted to the muzzle which makes it seem a little chunky.  If you want to drill out you also need to sand down the outer barrel.



The other minor thing is that the turret has the mount for the white light searchlight on the wrong side.  You can blag it by using that to put on the PZB 200 LLTV and make a Leopard 1A1A2 but you still need to mount the searchlight on the LHS which needs two small pieces to be added.