Saturday, 15 September 2012

Great War - 1916 British (RFA)

I had two 10mm Pendraken starter armies from a long time ago, to fuel my interest in WW1 Eastern Front operations. As with most things it didn't take too much time until I had delved into the Western Front.  I took most of the Pendraken British packs to make sure I had a wide variety of poses and type of figures to create a 1916 themed Empire force.

These are the results of the Artillery forces (RFA) needed.  I have some more still waiting to get under the paint brush with Soft hats as well as a much needed Howitzer Battery.




Little trick I found when putting the guns together (applies to any 10mm gun probably) is to put a small drop of liquid green stuff into the hole first, then put superglue on the spigot and then push into the hole. Sets quickly and seems to give a stronger joint.


Friday, 14 September 2012

1/600th Aircraft - US Navy Fighters

Following the amount of work that detailing USN Aircraft generated I have broken the page up into management pieces. This page covers the USN Fighter Aircraft. For details of the fighters in the CVW-16 project you need to go here.
 

F-4J of VF-92 10 May 1972

Step 1 - Taking the TD late model Phantom as a base for this model (it is one of the better F-4 mouldings from these guys (but way better than anything I could do myself)).

Step 2 - Undercoat and base as normal, follow with a dark wash to pick up the panel lines and then finally go over with the fuselage colour and insignia white control surfaces and undersides. THEN as we are adding coloured decals (on clear decal film) the fin needs to be really lighted at the base to allow the yellow to show properly (white).

Step 3 - Re-black the cockpit and air intakes. Then add the cockpit detail.
For this aircraft I also added yellow on the wing tips and the top of the fin. The VF-92 aircraft have a black outline around the cockpit. I have tried both freehand in the past (VF-151 and VF-111 F-4s). This one used a decal as it was black.

Step 4 - National Insignia. I always put this on first as it means that the aircraft start taking on persona of the real aircraft. This F-4J has the Dom Decals small national insignia either side of the rear cockpit on the air intakes. I have gone a size up on the TOP left wing and BOTTOM right wing (I don't normally both with the underside markings) based on photos for this particular aircraft.

Step 5 - The VF-92 aircraft has NG as a tailcode split with a chess piece. This sat above a yellow dart shape. The whole decal had been made up on clear decal paper so the yellow needs a white base to show up. The black will come out on anything.

Step 6 - I added 7269 as the Bureau for this aircraft again made up decals printed at the same time as the tail codes.

Step 7 - Added NAVY in black using home made decals. I can't find the recent pack of NAVY that Dom sent me Oh well.


Step 8 - Added the Modex Numbers 211 under the cockpit on both sides. Modex numbers were done using font size 4. Red traingles added to the cockpit sides for both Pilot and RIO. The Modex number on the real aircraft has a yellow shadow but that was a bit to fiddly to add.

Step 9 - The One Below: Fixing the errors and bits missing you will have picked up in the one above.

  • I have no idea why I painted white across the rear edge of the entire wing. I haven't done that on any other phantom so why this one ? The middle panel should be all white upto the N in NAVY. FIXED
  • I haven't done VF-92 for the squadron. Bit too fiddly. NOT GOING TO ATTEMPT ON THIS ONE
  • USS CONSTELLATION needs to come down a bit on both sides. This is a result of having separate decals due to the way that Microsol affects the paper. NOT GOING TO ATTEMPT ON THIS ONE
  • Ive done the white base for the yellow fins and wing tips, but forgot to put the yellow on! FIXED
  • Haven't done the natural metal on the rear surfaces and what isn't metal should be all white. FIXED
  • Haven't done the warnings at the air intakes. STILL NOT DONE
  • Haven't done the anti-reflection panel forward of the cockpit. DONE
  • NG needs adding to the right wing. DONE
  • 7269 on the starboard side needs replacing. DONE


  • A simple 1967 RF-8 Crusader.
    Step 1 - Clean up the model. The Tumbling Dice model has the sidewinder/Zuni mounts just under the cockpit on both side. This needs cleaning up with a file.
    Step 2 - Undercoat and base coat as normal, follow with a dark wash to pick up the panel lines and then finally go over with the fuselage colour and insignia white control surfaces and undersides.
    Step 3 - Re-black the cockpit and air intakes. Then add the cockpit detail.


    Step 4 - National Insignia. I always put this on first as it means that the aircraft start taking on persona of the real aircraft. The RF-8 has the Dom Decals small national insignia either side of the cockpit, TOP left wing and BOTTOM right wing (I don't normally both with the underside markings).
    Step 5 - Tailcodes. I chose to use the PP used by VFP-63 on USS Hancock. Simply because it is a simple "normal" PP (and I had the BuNo and Modex assignments). These were done on a word processor using font size 7 (which is approxmitely 36").
    Step 6 - Bureau Numbers were added again same font but this time down at size 2.5 (about 12") on both sides
    Step 7 - Added NAVY in black I have done some of my own for the more awkward TD aircraft where Dom's won't fit without hacking apart.
    Step 8 - Added the Modex Numbers under the cockpit on both sides. Modex numbers were done using font size 4. Red triangles added to the cockpit sides.
    Step 9 - Fixing the errors and bits missing.

    All said and done enough for wargaming models. Most of the markings are the wrong scale but I work on the TLAR principle (That Looks About Right). It gives the right impression. The VF-92 Insignia is also sat too far back, probably need to shift the NG forward as well just a fraction when I next do a decal run and a second aircraft
    Second models are always easier. A Black Falcons (VF-96) F-4J. Dropped the triangles but put the jet intake strakes on instead.

     

    Time to put this one into the varnish and then just some testors dullcote from the nice people at Antenociti's workshop so will give it a blast with that when it arrives (gives the varnish some time to harden as well). Panic over then the dullcote works and the two F-4s ready to go tableside.
    The beauty with downtown is that all aircraft represent flights so I can "do" individual markings for all my aircraft and not feel too guilty or I can run them all from the same squadron. The choice is limited by the ink in the printer and time to research.
    Part of the work to do a set of decals for USS Oriskany meant that I could get around to the proper fighter of the Vietnam war, the Crusader. VF-111 were one of the unique (if not the unique squadron) in that they had MiG kills with both the F-8 and the F-4. I had alread done a Sundowner F-4 when first getting into this scale so I was itching to get my hands on the F-8s. The tail art is a lot more reserved than later which was good as it took a while (and still needs updating as we go).
    As usual this simple foray led to more and more work and I have now done a test set for VF-111, VF-162, VA-163, VA-164 and VFP-63. I haven't done any of the support aircraft yet.
    I have now just finished the last of the 6 aircraft for the Constellation Air Group which took longer than I expected because I got diverted off to playing Ambush Alley. These F-4Js will go off for a game next Monday and the Cheltenham Warchiefs club for a game of Thud Ridge. These new ones have new proper length fuselage stripes (they are shorter). By doing so I have been able to add the Squadron identifier which was missing from the first two. For some reason I put 3 digit numbers on the elevators by mistake but only noticed after varnishing, oh well....Anyway TLAR and on to the table with these. Attack aircraft here I come.

    Moving off Vietnam for a little experiment I bought a pair of F-14 for a 1975 what if scenario. I have now done one of them (in the process of doing the second one) for TOPGUN. Only a little bit of fun.

    1/600th Aircraft - Painting Guide - Luftwaffe 1940

    For my 1940 era Luftwaffe Aircraft this is my starter method.
    • Undercoat white at this scale due to the need to preserve scale effect. Using a thin paint for the next layers gives you a slight shadow in the panel lines which you can then pick up with a wash later (GHQ Painting tip I found to be excellent. I cannot remember the last aircraft I painted with a Black Undercoat).
    • For lower fuselage I use GW Astronomican Grey from the Foundation paints.
    • Upper surfaces use a Field Grey for the RLM 02 Grey and currently I have some Tamiya Dark Green (XF-61) which I am using until some more Valejo paint arrives from Dom. I use GW Badab Black along the panel lines with 0 brush after the initial coats then add a little Vallejo Dark Sand to the Grey and recover. The Green is dark enough already
    • Cockpit and Glass areas use my tried and trusted method of Shadow Grey followed by a GW Badab Black wash then gone over again with Shadow Grey then Astronomican Highlights (I normally use Ghostly Grey but this has been discontinued for years so I needed to find a replacement).
    • Acrylic Varnish to give the Decals something to sink into
    • Apply Decals (use scissor and not a knife to cut out as you get a cleaner image)
    • Second coat of Acrylic Varnish to seal the decals
    • Dullcote to finish





    1/600th Aircraft - Painting Guides - Nesher

    My 1973 era Neshers painting guide



    • I undercoat the model white to start with.
    • Then I cover the upper surfaces with a thinned Vallejo Iraqi Sand
    • Then add the brown camouflage elements using GW Calthan Brown
    • Then add the green cam using GW Knarloc Green
    • Wash the model with Devlan Mud
    • Make a 50:50 mix of GW Blazing Orange and Iyanden Darksun and paint the triangles on wings and tail
    • Varnish the model
    • Apply the decals which are just black lines and numbers
    • Microsol the decals
    • Then taking the Iraqi sand again touch up all the sand areas to light and remove any orange peeping out from under the decals
    • Add Dom's Decals National Insignia
    • Varnish again to seal the decals in
    • Dullcote the whole thing
    I thought about using the white decal paper but to be honest it is a lot thicker and as such doesn't sit well. Some people get on with it so it is a personal preference.

    The tail art is trimmed pretty tight to fit and the serial number is part of one decal which made fitting a lot easier.

    Again not quite finished. I have two more in progress which MIGHT have more done to them. The big black aerial looks way ott so might get removed completely or painted a more inconspicious colour